Neue Klebefolie am Google Pixel 6 anbringen

Geschrieben von: Clay Eickemeyer

Kommentare: 33

Neue Klebefolie am Google Pixel 6 anbringen

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

30 - 45 Minuten

Einleitung

Diese Anleitung wurde von iFixit-Mitarbeiter:innen verfasst und ist keine offizielle Reparaturanleitung von Google. Hier erfährst du mehr über unsere Qualitätsstandards.

Diese Anleitung zeigt, wie die Klebestreifen im Google Pixel 6 nach einer Reparatur wieder angebracht werden. Das Display muss vorher ausgebaut worden sein. Wenn das noch nicht passiert ist, dann folge dieser Anleitung.

Werkzeuge

Ersatzteile

Google Pixel 6 Display Adhesive - Genuine

Schritt 1

Wenn noch Reste vom Kleber zurückgeblieben sind, wird das Display nicht gut haften.
Schabe mit dem flachen Ende des Spudgers soviel Kleberreste wie möglich ab.
Achte darauf, dass die Federkontakte am Rand des Rahmens nicht beschädigt werden.
Ziehe noch verbliebenen Kleber mit dem Finger oder einer Pinzette vom Rahmen ab.
Reinige den Rahmen rundherum mit etwas hochkonzentrierten Isopropylakohol (mindestens 90%ig) und einem fusselfreien Mikrofasertuch.

Schritt 2

Wenn du das Display weiterverwenden willst, dann reinige es genauso.

Schritt 3

Bevor du die Klebefolie befestigst, lege sie erst probeweise über den Rahmen, um die endgültige Position zu finden.
Orientiere dich an den Ausschnitten für den Lautsprecher sowie der unteren linken und der oberen rechten Öffnung, um die Klebefolie richtig auszulegen.

Schritt 4

Fasse die Lasche auf der Rückseite an und ziehe die Schutzfolie ab.
Dadurch wird die Klebefläche auf der Rückseite freigelegt.

Schritt 5

Arbeite bei diesem Schritt sehr sorgfältig! Der Kleber haftet sehr stark, wenn er einmal festklebt, kann er nicht mehr neu ausgerichtet werden. Falsch aufgeklebte Folie kann dazu führen, dass die Versiegelung nicht funktioniert.
Lege die Klebefolie an der Unter- oder Oberkante beginnend auf den Rahmen auf. Korregiere ganz leicht, während du sie nach und nach festklebst.
Beim genauen Ausrichten helfen die Öffnungen in der unteren linken und oberen rechten Ecke.

Instructions and photos should be clear about not touching any part of the edge where the adhesive is exposed. It appears as if it's okay if your fingers tough the edge, but you can't let any of the adhesive touch anything or else it will stick so badly that it stretches and no longer will adhere cleanly and flatly on the edge of the phone. I will need to buy a new adhesive andy phone is wide open and exposed in the meantime.

ALR -

Schritt 6

Drücke die Klebefolie rundherum mit dem Finger oder dem Spudger auf dem Rahmen fest.
Achte darauf, dass die Federkontakte am Rand des Rahmens nicht beschädigt werden.

Schritt 7

Fasse die Lasche in der oberen linken Ecke des Rahmens und ziehe die große Deckfolie ab.

Don't remove the final skinny liner around the outer adhesive - only remove the big liner. Leave the skinny blue liner in place until step 10 after the bracket has been attached.

Amanda B - 05/05/24

Schritt 8

Wenn du das Display ausgetauscht hast, dann kontrolliere die Öffnung für die Frontkamera und den Ausschnitt für den Sensor. Entferne alle noch vorhandenen Schutzfolien.

Schritt 9

Gehe wieder zurück zur Anleitung für dein Smartphone und setze den Zusammenbau fort.
Vergiss nicht, die Halterung des Displaykabels zu befestigen.
Komme dann wieder hierher zurück, wenn dein Display fertiggestellt ist und das Smartphone zugeklebt werden kann.

My new screen came with a tab on the selfie camera opening. Remove before sealing!

Alex Thengvall -

Guide fails to add step or note to reinstall the metal bracket and screw sitting on top of the display cable connector. I followed guide and resealed my phone only to realize this was not mentioned and now my phone is sealed without the bracket..

Derek -

Hi Derek, we're sorry that an instruction was missed! In this case, which guide did you follow to continue reassembly?

Clay Eickemeyer -

Would be good to add some tips on re connecting the display cable connector - took a bit of fiddling.

bogdan dobrin -

I plugged the screen cable in with the screen hanging over the right side of phone, snapping both top and bottom of the cable in. Then I moved the screen back to the left and put that metal bracket in place. Does anyone know if this is the correct way. There wasn't instructions on this part.

Simon B -

I missed a step or misread instructions and pictures. cleaned all the adhesive off the digitizer and put new adhesive on digitizer plugged it all in realized screen has digitizer on it.. the good news is all these missing steps means I order another adhesive. Almost broke screen getting it off.. be careful..

The bad news is I really don't recommend these directions.

Simon B - 23/01/25

Schritt 10

Achte darauf, dass du den Akku nicht mit der Pinzette anstichst, aus einem beschädigten Akku können gefährliche Chemikalien austreten, oder er kann in Brand geraten.
Fasse die Lasche an der unteren rechten Ecke des Rahmens und ziehe die Schutzfolie rund um den Rand ab.
Achte darauf, dass die Klebefolie nicht mit abgeht.

Add an image of the screen already connected with the display cable. It should eliminate any confusions (it's way easier to fiddle connecting the display cable when you don't have to worry about touching the adhesive (like I did).

bogdan dobrin -

This layer should be removed ONLY when the screen is connected and tested !

LGRI -

Directions and order of steps are not clear. There should be an earlier warning about keeping the final liner on. It was confusing when the large liner was peeled off because you don't know if the final liner should or should not stay on.

ALR -

The liner was like 1mm longer than normal, so while laying it down it clipped one of the sides but didn't notice until I took off the first liner.

To my dismay, it was not the most simple task up pull up the adhesive from the inner side wall of the device to lay onto the flat track it is meant to go on, but I did the best I could.

I'm hoping that when I go to cure the adhesive it'll flatten out the way it's supposed to for surface area, as well as maintain water resistance.

The first time I performed a screen replacement (this is 2nd) I actually was able to submerge device with no water leakage so if done properly (and the sheets are cut to specifications) it is very possible to retain water resistance after screen replacement

Zachary (Zach) - 24/06/25

Schritt 11

Drehe das Display um und lege es auf den Rahmen.
Drücke das Display rundherum fest.

I wish there was a warning here not to close the screen without testing it if reinstalling one. I thankfully was able to separate my newly installed screen and discover my display cable connection wasn't fully attached, but I am not sure if I compromised the seal or not. We will see!

Edward Rowe -

Schritt 12

Damit der Displaykleber besser am Rahmen haftet, muss er gleichmäßig angedrückt werden. Die Kameraleiste muss dabei berücksichtigt werden.
Wenn du Display-Schraubklemmen hast, kannst du die Kameraleiste aussparen. Bringe die Klemmen am Rand des Gerätes an..Screen Vise Clamps 6-Pack
Schütze das Rückseitenglas am Rand mit Klebeband, so dass es keine Kratzer bekommt.
Platziere Münzen oder ähnlich dicke Gegenstände an den Rändern des Rückseitenglases. Achte darauf, dass sie mindestens genauso dick wie die Kameraleiste sind.
Lege einen Stapel von Büchern oder andere schwere Gegenstände auf das Smartphone. Lasse sie dort mindestens eine halbe Stunde lang liegen, am Besten über Nacht.

Would be useful to list these coins (spacers) as a requirement for the installation. Not everyone has coins or similar spacers around.

bogdan dobrin -

Excellent guide. I recommend reading through it a couple times before starting, but really good instruction.

msqualls -

Tinte & Feder

Clay Eickemeyer

Mitglied seit: 19/09/22

85412 Reputation

18 Kommentare

Clear and to the point guide, which worked perfectly from the first go, kudos!

Ken Lammrtyn -

Why not align the adhesive with the liner covers on?

-Remove the display side of the adhesive then attach display to phone. Then adhesive should be lined up on the display and you should only need to remove the phone body adhesive cover and press the phone and display together.

Beau Ellerson -

Hi Beau! This is a clever idea. We've taken this approach with some simpler adhesives before. While I can't say exactly why it wouldn't work, I can assume that applying the adhesive the screen-side-first will make it more difficult to visually check that the adhesive lined up properly on the screen. It doesn't seem impossible for any reason, though.

Clay Eickemeyer -

where is the guide for reassembly?

Caspar Redgrave -

The exact guide depends on which phone you have. Click here for the list of Google Pixel 6 guides, pick the guide you were working on, and find where you left off!

Clay Eickemeyer -

This is an excellent guide, thanks for the effort.

For others who attempt this; getting rid of the old adhesive is really time consuming, it took me a good hour or so to get it all off the body and screen.

Oli -

Absolutely, while some of the other steps during disassembly were stressful and difficult, removing the old adhesive was far far more time consuming.

Leo Huang -

Hello, i have purchased a screen repair kit for a pixel 6, after reassembly I noticed the proximity sensor is not working, any help would be appreciated.

Alexandru Mitrea -

I'm sorry to hear that your proximity sensor isn't working! This might be best handled by our customer service. Check out https://help.ifixit.com/ to get in contact with us, or see some troubleshooting steps.

Clay Eickemeyer -

Hi guys, just bought a kit after my screen came loose after a few knocks. What are the spring connectors on the Pixel 6, and what is their purpose? My screen works as of right now, but has no sensitivity on the upper third of the screen, and typing only picks up half the letters. I imagine it has to do with a broken digitalizer and not with these connectors, right?

Dani Cornes -

It could be due to an improper calibration. Try running your fingerprint calibration software again and, after making sure nothing has touched the screen during the process, reboot the phone manually after the process is all done. Problems with the calibration or not allowing the phone to reboot this additional time can cause touch issues with your new part.

Clay Eickemeyer -

When do you Plug the screen in and replace the little metal holder?

Melissa M. Miko -

Hi Melissa!

In this guide, this step is the point in which you'll return to your original replacement guide and continue reassembling your phone. This is where you'll reconnect the screen and install the metal bracket. Then, follow the rest of the steps to finish sealing up the screen.

Clay Eickemeyer -

Hi. The phone is now 2mm thicker than it was with the genuine screen, is that a normal thing?

Cyril -

Please add to manual to double check if proximity sensor seal wasnt removed with previous screen. Do not repeat my mistakes!

Vitalii Zhyrun -

What happens if i busted the spring connectors? I kinda hate how everyone is copying apples antics when assembling these devices, it only gets harder every time and mostly for no good reason than profit.

Ion D. Éfeso -

On the back of my screen I noticed an x over the fingerprint reader.. and my fingerprint reader is not working. Is the x telling me this and what do I need to do?

Carey K -

It would be nice to add a note about the plastic outline frame that may come off separately from the display when dismantling; make sure to remove this plastic frame with the display before adding any adhesive. If the surface that should be in contact with a new screen is gray (not black), it means the frame is still glued into the phone and needs to be removed.

Clovis Delmotte -